During my 4.0L Whipple install recently I was discussing the viability of adding an Air/Oil separator on the PCV line since I have seen and heard about how much oil is in the intake of these motors when you remove the supercharger. With the increased boost levels we see it becomes much more important; reducing the oil in the combustion chamber and lowering the effective octane rating of the fuel and keeping an oily film off intercooler core thus reducing it’s ability to transfer heat among other reasons. Evan Guyett told me that they were working on a design for this and getting close to finishing a version just for the FGT along with an complementary breather tank for the transaxle. We agreed that my car would get both during the install of the Whipple S/C. Evan installed the two tanks and they look as if they came OE on the car, just as he said they would. He said the Air/Oil separator has three different separating circuits in the unit along with a safety bypass should the unit become completely full. They even put a sight glass in the reservoir like the other reservoirs in the engine compartment. This is definitely a must-do in my opinion.
Oil Separator
- Thread starter cobra498
- Start date
BlackICE
GT Owner
2112
Blue/white 06'
DanielJ
GT Owner
Evan did the PPI on my GT and spent the majority of the day with me. He is a class act through and through!
BlackICE
GT Owner
2112
Blue/white 06'
We have a design in the works and have a prototype nearly done. Definitely plan to debut it at the Rally in August if not sooner. It will be custom kit for the GT with everything needed. The catch can component is, in our opinion, the best on the market and we've looked at a lot.
eg1985
GT Owner
The Air/Oil separator I prototyped on Bruce's car was developed over months of working closely with one of the top oil system manufacturers on the market who make the majority of the oil system components for the NHRA Top Fuel, Funny Car, Pro Stock, and Pro-Mod guys as well as many of the World of Outlaws and road race teams. Ever since the first time I removed an FGT supercharger I noticed the excess amount of oil in the intake and coating the rotors on the supercharger. I originally looked at what was available, but after looking closely at the current designs out there, I started with a clean sheet of paper and made my own. First and foremost I wanted the function to be flawless with enough thru-flow to as not create any seal and gasket sealing issues under extreme crankcase pressure (a problem many of the Hi-HP turbo diesel crowd has faced for years) and Secondly, I wanted it to fit and look absolutely like it was OE on the car. Where this one differs is in the internal construction, and without giving too much away, I can say that it utilizes no less than three separation stages as well as a by-pass should the reservoir become completely full (highly unlikely due to the OE sight glass). We built the separator to bolt on in just minutes using existing bolt holes already in the chassis and without any modification to even the OEM PCV hose. I also built a matching breather tank for the transaxle that also bolts on and finished them both in the OEM Mini-Tex finish to match the other underhood reservoirs. Here's a pic on Bruce's car:
I'm currently in production making a few of these thanks to Bruce showing them off.
I'm currently in production making a few of these thanks to Bruce showing them off.
Last edited:
eg1985
GT Owner
BlackICE
GT Owner
The Air/Oil separator I prototyped on Bruce's car was developed over months of working closely with one of the top oil system manufacturers on the market who make the majority of the oil system components for the NHRA Top Fuel, Funny Car, Pro Stock, and Pro-Mod guys as well as many of the World of Outlaws and road race teams. Ever since the first time I removed an FGT supercharger I noticed the excess amount of oil in the intake and coating the rotors on the supercharger. I originally looked at what was available, but after looking closely at the current designs out there, I started with a clean sheet of paper and made my own. First and foremost I wanted the function to be flawless with enough thru-flow to as not create any seal and gasket sealing issues under extreme crankcase pressure (a problem many of the Hi-HP turbo diesel crowd has faced for years) and Secondly, I wanted it to fit and look absolutely like it was OE on the car. Where this one differs is in the internal construction, and without giving too much away, I can say that it utilizes no less than three separation stages as well as a by-pass should the reservoir become completely full (highly unlikely due to the OE sight glass). We built the separator to bolt on in just minutes using existing bolt holes already in the chassis and without any modification to even the OEM PCV hose. I also built an complementary breather tank for the transaxle that also bolts on and finished them both in the OEM Mini-Tex finish to match the other underhood reservoirs. Here's a pic on Bruce's car:
I'm currently in production making a few of these thanks to Bruce showing them off.
Very cool, much needed product. I was amazed at the oil I found when I install my Whipple with only 2K on the motor.
eg1985
GT Owner
Thanks Daniel! I hope you're getting lots of enjoyment out of your new car. :thumbsup
That prototype looks amazing.
JLT Performance makes a really nice billet one for the GT500.
http://jlttruecoldair.com/ZenCart/index.php?main_page=product_info&cPath=266_269&products_id=317
The glass versions seem out of place in the engine compartment.
I always wondered why the GT SC does not have an oil separator.
Please post more pics and feedback.
JLT Performance makes a really nice billet one for the GT500.
http://jlttruecoldair.com/ZenCart/index.php?main_page=product_info&cPath=266_269&products_id=317
The glass versions seem out of place in the engine compartment.
I always wondered why the GT SC does not have an oil separator.
Please post more pics and feedback.
eg1985
GT Owner
fjpikul
GT Owner
There is a long thread here with a trick, inexpensive setup pioneered by StormCat. Please do a search.
MAD IN NC
Proud Owner/ BOD blah bla
2112
Blue/white 06'
Mark did you install this?
http://www.namotorsports.net/detail.cfm/part_cd/DD42-CCU-012
Even has a dipstick!
http://www.namotorsports.net/detail.cfm/part_cd/DD42-CCU-012
Even has a dipstick!
2112
Blue/white 06'
Howard
GT Owner
I have the Stormcat-developed system in my GT, and although you cannot beat its cost I don't think it captures all the oil being vented into the S/C. I say this because it very rarely needs emptying despite the small size of its reservoir. I am in the process of installing a Moroso separator much larger than the Jegs unit I presently have, but apparently smaller than the new one being developed, above. I bought the Moroso device the day before the new one was announced!
Howard
Howard