Is your GT modded?

[FORDGT001]

Bone Stock.

 

[Shadowman]

My gal is just as I envisioned she would be prior to her arrival however sadly there were a few items that they failed to tend to that were on my must have list as such I was compelled to massage her a bit.

She appears, sounds, and runs as OEM as such if the old saying "if she looks like a..... sounds like a..... then she is a ....." holds water then my gal is OEM

Takes care

Shadowman

 

[ChipBeck]

Glovebox

"Ford factory leather covered glovebox between the seats"?? Tell me more. What is this? Photos?
Howard

Howard,

In non-Macintosh GT's there is no giant speaker between the seats. In place of that speaker is a cool leather covered glovebox. It looks much nicer than that big speaker (which is now relocated behind my passenger seat) and provides some much needed storage space.

Chip

 

[BlackICE]

She appears, sounds, and runs as OEM as such if the old saying "if she looks like a..... sounds like a..... then she is a ....." holds water then my gal is OEM

Takes care

Shadowman

What looks OEM, until you open a door?
What sounds OEM, until you start the engine?
What runs like OEM, until you get on the boost?

Answer, only the Shadowman knows.

 

[Shadowman]

What looks OEM, until you open a door?
What sounds OEM, until you start the engine?
What runs like OEM, until you get on the boost?

Answer, only the Shadowman knows.

LOL; you are a good man

Considering that she is as she has been since she had only approximately 50 miles on her gives me little else to compare to

She is thoroughbred through and through and makes me smile whether I am looking at, getting in, or getting out of her not to mention that when I press the "GO" button I become akin to a kid in a candy store.

Ford did very good in my eyes

Takes care

Shadowman

 

[Howard]

Chip, thanks for the info and photo. I didn't know that that the non-Mac GT's had a storage bin. I'll have to consider a speaker-relocation project.

Howard

 

[911teo]

...

Functional Brake Ducts

...

More info PLEASE....

The fake brake ducts holes are really bothering me.

The whole car is magnificent, a masterpiece, but the fake holes... :thumbsdow

How did you do it? I was under the impression that you need to lose the A/C (compressor in the way on the passenger side).

Thanks for your help.

PS
the rest of the list is just IMPRESSIVE!

 

[DRIVEBY]

Running duct tubes all the way back to the wheels is a tight mess. Without moving anything, my shop was able to work around most lines and even had some intersecting through the tubes. You can actually see the compressor and a/c lines inside of the ducts. Yes they are there, but don't significantly detract from air flow. The job is very involved and probably not worth the hassle as the whole front of the car has to be dismantled - i.e. $$$. I would take some pics for you, but I just dropped the car off this afternoon for measurements on a new Brembo GTR Braking system. The blocked of ducts do look kinda bad, but if it's brake cooling for cheap your seeking, maybe bring the air from underneath like the vents on the newere 911 racers.

 

[06fordgt]

Cooltech Tranny Cooler
Cooltech Seat Stops driver and passenger sides
Cooltech Bettery Tender
Accufab TB
Accufab Axle Bolts
Accufab Drain Plugs
Ford OEM Short Shifter
Ford OEM Shifter Ball
Ford OEM Seat Covers
Ford Dealer Intake Support
Derry's Custom Wheel Nuts
Blue Engine Light
Custom Floor Mats
Safecraft Fire Suppresion System
Venture Shield Paint Protection & custom sections
Wiper Delete
Rear Back Up Camera
Cooltech Brembo Brake Caliper Decals
Ford GT Badge
Tire Paint (still to do)
Personal Plate
License plate cooling spacers
Black license plate frame
:thumbsup:thumbsup:thumbsup
WOW can't believe how much has been dione so far. While most are not performance mods still been a blast doing all this stuff and best of all Driving!!
More to come-
Exhaust, pulley and tune- Still undecided as to which set up to use.

 

[06fordgt]

The black/silver stripe is bone stock. Have Derry's custom wheel nuts for this car as well but not installed. Still in the beautiful case that Derry sends them in. Still with all original factory stickers on the car and plastic seat covers on the seats.:banana

 

[DanQ]

No engine mods.

Cool Tech transaxle cooler
Carbon Fiber mac delete panel
JVC NX5000 NAV, DVD, HDD Bluetooth, MP3
Accufab magnetic drain plugs
Custom Floormats with blue piping
License plate cooling spacers
Trans Vent Can

Not installed:
Accufab SCT
Accufab radiator hose springs
Accufab Air Intake support (not needed on late '06?)
Accufab Axle bolts

 

[dbk]

I bet this answer would surprise a lot of people. Not I :biggrin

I'd like to see at least another 150 responses eventually...

 

[dikran]

Smaller Pulley
Ford OEM Racing Muffler
Ford OEM Transaxle Cooler
Ford OEM Short Shifter
Ford OEM Shifter Ball
Ford OEM Seat Covers
Ford OEM Chrome plated fluid covers in the engine compartment
Derry's Custom Wheel Nuts
Custom Floor Mats
Personal Plate
Brushed silver license plate frame

 

[ByeEnzo]

iPod hookup to Mac stereo
Ida catback exhaust (Jet hot coated)
Ida cold air kit (vent blockers)
Classic concept designs bumper delete
Ford Racing Transcooler
Accufab TA bolts
"Upgraded" to stock wheels, Hoosiers on the lite BBS wheels for track use
Drivers seat lowered for helmet use
Cobrar's harness bars
Schroth 6 pt. harness
1 degree increased neg camber all around
Ed Sims "Ferrari Slayer" decal
Safecraft engine fire suppression system
Safecraft passenger side fire extinguisher
Clearshield all around car
Windshield protective film
Windshield wiper delete

 

[STORMCAT]

my list is long .. CF and Blue lights that's all you need to know !!!

 

[HeritageBruce]

Just a few mods in the order it was done to the car. Is there any part of my car that's still under warranty?
3M Clear Bra
$1.99 cup holder (yes one of the most important mods here)
Acufab Xpipe
Acufab throttle body
Acufab intake stiffener
Kenne Bell Snout (replaced by Whipple later)
Cooltech Transaxle cooler
Moton Motorsport Shocks
Subwoofer relocation
Crimestopper license plate frame camera
Lowered driver seat by 1 1/2"
Removed rubber mats for Llyods mats
Removed wipers
Gel left elbow pad
Ford Racing Short Shifter
Personalized plate - AKA GT40
Razo Shiftknob
Safecraft fire extinguisher
Acufab Axle Bolts
Whipple with 19# pulley
SCT Livewire
LC1 wide band O2 sensor
AP Racing Brake Upgrade (front and rear)
Kip center console w/ storage
Kip door trim ring
JVC navigation head unit
Russ' harness bar
Schroth 4 point belts
Stormcat center panel (on its way)
Hopefully some new R compound rubber soon

 

[BlackICE]

HeritageBruce, how do you like the Livewire? Does it do datalogs without a PC? If so do you have any idea on how long you can collect data with less say 10 PIDs? I am sure the more PIDs the less time. The last I heard about the Livewire unit, is that it wasn't ready for prime time.

 

[Dino]

I guess we are considering any mods, no exceptions for parts from Ford Racing.

 

[STUNTS]

O.......G........

OHHHHHHHHH
Jeeeeeeeeeeee

all origanal here.......

trust me, I've wanted and not wanted...... but she's staying all natural..... I think....... for now anyways..... probabaly

well..... maybe

:confused

 

[911teo]

HeritageBruce

How did you lower the seat? I have clearence problems with my helmet, so much so that I am considering purchasing a door and have a Gurney bubble installed...

But before I do that I would try any other possible solution... 1.5 inches could solve my problem.

Thank you